CALL CART ACCOUNT

ITEMS IN CART: 0

$0.00

translate
Tag Archives: SureFit
  • Repairing Nail Pops - There's No Joke About This Tricky Project

    It might be April Fool's Day, but we aren't joking around with this tricky project, repairing a nail pop. Nail pops occur over time, when a nail begins to separate from the stud it is anchoring drywall to. As the nail begins to work itself out, it eventually applies enough pressure to the spackle or putty above it, to force the putty away from the drywall - eventually exposing the nail's head. Nail pops can be caused by a variety of reasons - from wood beams that swell with humidity to a settling foundation.

    An occasional nail pop is nothing to get excited about, but if you notice other problems such as severe cracking, bulges or discoloration in your walls and ceiling - consult a building inspector to have your home evaluated for a more serious issue. More often than not, a nail pop is caused by the convergence of warm and cold climate(s), which causes wood to swell and contract. They are also more common in older homes, as screws were not a preferred method of drywall fastening 20-30 years ago. Current builders and contractors have the option of using a screw gun, such as Senco's DuraSpin tools, when installing drywall. In the past, nails and nailers were typically used for drywall installation. Because a nail has a smooth body, it doesn't command the same holding power that the tracks on a screw do - making it easier to slip out of position.

    There are a couple ways to repair a nail pop, depending on the arsenal of tools at your disposal. The simpler solution, take a nail punch to the center of a nail pop, and lightly tap it with a hammer. In the unlikely event that a screw has come loose, simply take a screwdriver and tighten. When using the nail punch, sheetrock and drywall will likely chip away if the nail has not completely protruded through yet, so you will have to use spackle to cover the opening; followed by smoothing, sanding and painting.

    A bit more complex, you can also drive a drywall screw into the drywall, along the same stud where the nail has begun to separate. This is a more permanent solution to the problem, as the screw should secure the drywall in place - whereas using a nail punch does not guarantee the issue will not recur if the nail re-separates. Once the screw is in place, scrape any leftover sheetrock or putty away from the original nail gap and spackle over both the nail and screw opening(s). Smooth, sand and paint as necessary.

    Nail pops can be a tricky problem for homeowners, but can be easily repaired with the proper attention. If you don't feel comfortable repairing the issue yourself, consult a handyman or professional to remedy a solution for your nail pop.

     

    Your How To Helpers,

    The Team At Nail Gun Depot

    Read More
  • What Type Of Nail Is Correct For My Application?

    At the end of 2013, we posted about the various components of a nail and offered some in-depth explanations as to the importance of these components. If you missed our previous posts on nail components, here is a quick refresher - with some added knowledge.

     
    Collated nails are offered in a variety of degrees, sizes and types. This article will take you step by step in determining the classification, range, type and finish required for your application. A popular choice, check out Nail Gun Depot's SureFit nails, if you are looking for a high quality fastener at a fraction of the cost. Another popular choice, Senco nails offer a wide variety of fasteners to choose from, with genuine, time-tested durability.
     

    The first step is to determine what collation angle your tool is designed to run. Some degrees include 20 °, 35 °, 28 ° and 15 °. The next step would be to classify what types of collation the tool handles. Collations include plastic, wire and paper - which can be used in place of plastic.

     

    When you have completed the nail classification, you will then determine the tool range. The length and diameter are known as the range. Length is the size of the nail, each tool will have a minimum and maximum length. Note: some nails are sized in pennies (symbol, D). Diameter is the thickness of the shank or wire gauge. The bigger the number, the thicker the nail.

     

    The type of nail can be broken into three categories; head, point and shank. Head types include duplex, headless, finish, drywall, clipped and full round which is the most common. The type of point determines how the nail will penetrate into your application and the splitting severity. The most common is chisel (diamond) point and the easiest to drive. It is ideal for soft wood applications. Blunt point allows minimal penetration resistance and is commonly used in pallet construction. Flat point, also known as chisel point, requires the most drive power and is frequently used with a screw shank nail.

     

    The nail shank is the part on the nail which does most of the holding. The shank is one of four types: smooth, spiral, ring or screw. Smooth shank nails have exactly that: a smooth appearance and has the least holding power. Spiral shank nails have either a threaded appearance, like a screw, or they can have a helical twist to them. Screw shank nails are used in hardwood applications. Ring shank nails have a series of rings punched into the surface of the shank and offers the most holding power.

     

    The nail finish can be bright, cement coated, electogalvanized, hot dipped galvanized, flash-coated with zinc, hardened steel, stainless steel or aluminum. These different finishes, coatings or material of nails give different levels of protection of resistance to rusting or other special properties to certain applications.

     

    The factors mentioned above such as degree, collation type, nail size and shank diameter can all affect the compatibility of nails with any nail gun. Contact a Nail Gun Depot Customer Service representative to confirm compatibility and determine the best nail for your application. You can also use Nail Gun Depot's Fastener Finder Tool to locate the right nail for your tool.

     
    Here's To Nailing Your Next Project,
    The Team At Nail Gun Depot
    Read More
  • 2 Item(s)

Copyright © 2017 Nail Gun Depot All rights reserved. All trademarks and brands are property of their respective owner