ITEMS IN CART: 0
$0.00
An important step in nearly any major home renovation project? Installing drywall. Knowing how to do it yourself can save time and money. We offer you a few tips and discuss the best tools for the job, here on the Nail Gun Network.
Most new construction projects mandate the use of drywall screws when installing drywall. Screws are certainly ideal, as their thread provides better holding power, especially in climates where wood is prone to expand and contract regularly. In some circumstances, drywall nails can be used to hang wallboard, but beware; over time, nail popping and other imperfections to the wall might occur as the wood frame expands and contracts.
For long-term quality, we recommend using a screw gun and collated drywall screws for a fast, cost-effective drywall installation. Two competitive screw fastening systems, Senco DuraSpin and Simpson Quik Drive, offer best-in-class performance.
Another benefit to using screws over nails for drywall installation is that it generally takes fewer screws to complete the project. Pro Tip: Most drywall screws require a Phillips head drive.
Even for beginners, drywall installation is relatively easy to pick up. Just pay careful attention to the following:
Be certain to consult your local building code before beginning drywall installation, as different regions have different requirements. Beyond building code, don't fall victim to silly, yet expensive errors. Gather all of your tools, and don't forget the small one. For instance, have a tape measure handy to maintain straight lines.
As damp wood dries out, it can lead to popping of fasteners and splitting at seams. Make sure the lumber you are fastening drywall board to is within an acceptable range of moisture content (less than 19 percent by most standards).
Don't overlook sagging panels, particularly when installing a ceiling. Make sure to drive extra screws into place while pressing firmly on the loose board. In some extreme cases, an additional brace or bracket may be required to guarantee a firm fit. Likewise, watch for bulging at your vertical seams. If the drywall board swells at the seam once it's been taped and sealed, it may require sanding. You can prevent this issue by ensuring there is no gap between drywall boards during installation.
Use a corner guard versus drywall tape and spackle. A corner guard will hold up better in the long run and is typically easier to work with than tape. You should also mark your studs and joists prior to installation of a drywall board. This will help improve the accuracy of your drive and will prevent additional repair work in problem areas.
Don't ignore bubbles, streaks, splits or other noticeable imperfections in drywall tape as it is laid. If air is allowed between the tape and base, it will lead to separation later on. Tape that is not secured properly can eventually peel and will require repair and repainting. In areas where warm and cold air are allowed to converge regularly, eventual loosening and separation of tape from the drywall base is almost inevitable.
Depending on the thickness of the board, determine the appropriate screw length and depth adjustment for your screw gun. Driving too deep can cause noticeable divets in the drywall. Driving too short leaves the screw's head protruding. If installed properly, the screw's head should sit slightly below the drywall surface, leaving just enough room for compound to smooth the surface.
To recap, make sure your framing is dry, mark your studs and joists for accurate drive locations, hold the drywall board firmly against the wood frame while fastening in place, line up boards for accuracy, scan and repair imperfections, and enjoy.
~ The Nail Gun Depot Team
Getting ready to start a woodworking project? Maybe you aren't sure what tools you need to complete your project? Let's take a look at some of the tools you might need to tackle woodworking, whether starting your first project or just adding a new tool to your collection.
There isn't one specific woodworking tool that's more important than another for your workshop—it really just depends on the project you're looking to take on. Unless you get a battery-powered, cordless fastening tool, you will need an air compressor to power any nail gun or staple gun you purchase.
If you're just getting into woodworking or DIY projects around the home, you'll probably want to start with a finish, brad or pin nailer. These tools are most commonly selected for smaller woodworking projects such as furniture and cabinet building, trim work, and craft projects.
Similar to a finish nailer, you might also consider a finish stapler, depending on the small project you're working on. Staple guns can be particularly useful for furniture and upholstery projects. Upholstery staplers are an absolute must-have tool if you're refinishing a chair or sofa.
Looking for something a bit larger to build? For sheds, home additions, tree houses, or anything else that requires a structural frame, you'll need a framing nailer. These nail guns have the power to drive large framing nails, which are mandatory for any structural project. Once a structure has been framed, you might find a screw gun useful for adding any finishing touches to your project, such as drywall or deck boards.
Last, but not least, don't rule out a palm nailer as a viable option for less intense projects, particularly ones that require touching up those hard-to-reach areas. A palm or hand nailer, as they're also known, is typically used for framing, decking, fencing, pole barns, metal connector straps and other similar applications. While palm nail guns don't offer the benefit of a collated drive to hold a large capacity of fasteners, palm nailers are small, and capable of reaching hard to access areas where a large tool would be unable to fit. Another benefit to palm nailers; you can find most priced below $100.
Ready to start your project? Need more help? Our trained customer service team is ready to pair you with the right fastening tool for your project.
~ The Nail Gun Depot Team